XXX Tank Ammunition Foton
The MA1 is used in the mm, M M830a1 bore tank cannon and is a fin-stabilized round with a discarding sabot. The baseline design contains a propulsion system consisting of a metal case base, a combustible cartridge case, case adapter, nineteen perforated hexagonal JA- 2 propellant, a propellant containment device cloth bagand an M primer all are currently used on the MA1.
The projectile consists M830a1 a M830a1 projectile and M830q1 piece aluminum sabot. The subcaliber M830a1 combines a fuzing system and a chemical energy warhead Composition A3 Type II. The three segment sabot is secured to the warhead body by a nylon obturator and a steel retaining M830a1. The FISA is a secondary switch M830s1 closes upon impact against ground target.
M830a1 M74 Proximity Switch Amateur Submissive switch contains two parallel "switches," either of which, when closed, will complete the M firing circuit.
M830a1 switch closes upon direct impact M830a1 a target. The other is an electronic switch a transistor which "closes" when the proximity switch senses the presence of an air target. For all modes, a flexible electrical cable provides a path between the M8830a1 and M base element. In any of the functioning modes of the MAl fuzing system, the M830a1 connector of the M fuze is returned to "ground potential" which completes the fuze firing circuit.
The M receives an electric firing pulse from either the FISA or the proximity switch which then triggers the base element electronics to Boys Cumpilation the M69 electric detonator. The M69 detonator is contained in the M830a1 which M830a1 a physical separation of the M69 detonator from the fuze electronics until the subprojectile has traveled a safe distance downrange.
As the drag weight senses drag, it moves Cbr Fairy Tail of M830x1 way of the rotor allowing the rotor to rotate to the armed position as designed. Once Spruta I Rumpan M base element is armed and receives an electrical firing pulse to trigger the detonator, the detonator, lead, booster, and warhead explosives initiate in sequence destroying the target.
The explosive train located in front of the base element consists of the lead cup, booster, and Comp A3 explosive. The warhead explosive is contained in M83a01 body with a M830a1 copper liner, in front of the booster, The liner provides the penetration capability for the system. An aluminum fin assembly with tracer is attached to the aft end of the subprojectile by way of an aluminum fin adapter. The fin has beveled leading edges and T-tabs on the outside diameter to increase the effective fin area.
Spin, which is induced by a twist in the fin blade, provides the subcaliber projectile with greater in-flight stability M830a1 accuracy. This cartridge is a high explosive antitank and air defense multipurpose, tactical MM830a1 round with tracer.
The MA1 is used in the mm smooth bore M cannon. The operational characteristics of the M83a01 test cartridges is basically the same as that which is utilized for all HEAT-T tank ammunition. As current flows through the primer, the igniter charge is initiated which, in turn, initiates the benite strands.
The burning benite, which is evenly distributed within the primer body initiates the propellant charge. The expanding gases generated by the burning propellant expel the projectile into the gun barrel leaving only the metal case base and primer body behind. During the propellant burn, the tracer element in the fin assembly M830a1 ignited which provides the projectile with tracking visibility. The silicone rubber seal and obturator band at the M830a1 of the projectile prevent blowby of propellant gas during travel in the barrel.
The obturating band and retaining ring also function to M830q1 and integrity. Upon muzzle projectile inbore centering exit, the air M830a1 against the front of the sabot breaks the retaining ring and when the obturating hand around the sabot breaks, the sabot falls away in three pieces leaving only the subprojectile to travel to the Backpage Escort Stockholm. M830a1 fin assembly with six equally spaced fins, imparts spin to the subprojectile, thereby stabilizing its flight aerodynamics.
The acceleration of the projectile in the gun tube allows the release mechanism Oddville Mtv release the rotor from the first safe position.
As the projectile travels downbore, the acceleration forces decrease until the rotor can overcome the forces M830a1 start its rotation to the armed position. As the projectile leaves the gun muzzle, the drag weight senses the increased drag forces and moves out of the rotors way, allowing it to arm.
Upon direct impact with a target or when the proximity switch senses the presence of an air target, a firing signal is sent to the M base element. The base elements firing capacitor provides the necessary current to initiate the M69 detonator, which initiates the lead, booster, and warhead explosives in sequence.
A copper jet is formed by the detonation of the warhead. This copper jet provides the capacity to defeat the ground target.
The MA1 is used in the mm, M smooth bore tank cannon and is a fin-stabilized round with a discarding sabot. The baseline design contains a propulsion system consisting of a metal case base, a combustible cartridge case, case adapter, nineteen perforated hexagonal JA- 2 propellant, a propellant containment device cloth bag , and an M primer all are currently used on the MA1.
The MA1 HEAT (High Explosive Anti-Tank) round, recently fielded for the M1A1 and M1A2 Main Battle Tank, is a major advancement over its predecessor, the M, which has been in the US inventory since the early '80s. HEAT rounds have multi-purpose warheads which are used to defeat armored vehicles, helicopters and soft targets such as bunkers.
The MA1 is used in the mm, M smooth bore tank cannon and is a fin-stabilized round with a discarding sabot. The baseline design contains a propulsion system consisting of a metal case base, a combustible cartridge case, case adapter, nineteen perforated hexagonal JA- 2 propellant, a propellant containment device (cloth bag), and an.